CUSR 174315 Operating Instructions and Parts Manual 12" Sliding Dual Bevel Compound Miter Saw Benchtop Series – Model No. JMS-12SCMS F
10Features
11Shipping Contents Unpacking 1. Remove the contents from the shipping container. 2. Compare the contents of the shipping container with the list fo
12Assembly Unlocking the Slide Carriage Loosen the slide carriage lock knob (A). When transporting or storing the miter saw, the slide carriage (B)
13 Installing the Safety Hold-down Clamp 1. Place the hold-down clamp assembly (A, Fig. 4) in a mounting hole located behind the right or left fence
14Table Inserts Always unplug the saw to avoid accidental starting. Failure to comply may cause serious injury! ! Remove table insert to remove all
15Installing Blade Important: This machine requires a 12-inch diameter blade. Unplug the miter saw before changing and/or installing the blade. Refer
16Adjustments Before attempting any adjust-ments – To avoid injury from unexpected starting or electrical shock make sure the trigger is released an
17 2. Loosen the bevel lock handle (A, Fig. 8) and tilt the cutting arm completely to the left (Figure 11). 3. Using a combination square, check to
18Miter Angle The sliding compound miter saw scale can be easily read, showing miter angles from 0° to 45° to the left, and 0° to 60° to the right. T
19Positive Stop Miter Angle Adjustment Referring to Figure 19: 1. Unlock the miter table by lifting up on the quick-cam miter table lock (A). 2. Rai
Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Autho
20Presetting the Cutting Depth The depth of cut can be preset for even and repetitive shallow cuts. Referring to Figure 21: 1. Pull hold-down latch (
21Operation Before attempting any operation with your miter saw, make sure that you have read and thoroughly understand the warnings contained on pa
22Sliding Fence The sliding fence must be extended to the left or right when making bevel cuts. Failure to comply may cause serious injury! Failure
23Miter Cut Referring to Figure 26: The sliding compound miter saw has ten positive miter stop indents (A) located on the saw base. The stops represe
2433.9° Bevel Detent Pin for Crown Moldings Note: A bevel detent pin is incorporated into this machine for quick bevel adjustments when the desired b
254. Position the workpiece on the table and against the fence. Use a hold-down clamp (E) attached to the base, whenever possible. 5. Pull the trigg
26Cutting Bowed Material Always unplug the saw when removing small pieces of debris. Failure to comply may cause serious injury! Referring to Figure
27Cutting Base Molding Base moldings and many other moldings can be cut on a compound miter saw. The setup of the saw depends on molding characterist
28Crown Molding Chart Compound miter saw miter and bevel angle settings, wall to crown molding angles 52/38º Crown Molding 45/45º Crown Molding
29Maintenance To avoid injury while performing maintenance, always unplug the power cord before working on the saw. Failure to comply may cause seri
Table of Contents Warranty and Service...
30Troubleshooting – Motor Trouble Probable Cause Remedy Brake does not stop blade within 10 seconds. Motor brushes not sealed or lightly sticking.
31Parts Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848 Monday through Friday (see our website for bus
32Parts List Index No. Part No. Description Size Qty 50 ... TS-0680041 ...Flat Washer...
33Parts List Index No. Part No. Description Size Qty 108 ... JMS10SCMS-210 ...Cable Clamp ...
34Parts List Index No. Part No. Description Size Qty 166 ... JMS12SCMS-166 ...Bearing Protector...
35Parts List Index No. Part No. Description Size Qty 223 ... JMS12SCMS-223 ...Swivel Support Assembly ...
36Assembly Drawing
37Assembly Drawing
38Assembly Drawing
39Wiring Diagram
4 Auxiliary Wood Fence ... 26
40 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.walter
5 Warnings 1. Read and understand the entire owners' manual before attempting assembly or operation. 2. Read and understand the warnings post
6 23. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious i
7 Compound Miter Saw Safety Specific safety instructions for this compound miter saw 1. Do not operate the miter saw until it is completely assemble
8 Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for the JET Model
9 Electrical Power Supply and Motor Specifications The AC motor used in this saw is a universal, nonreversible type (see Motor in the Specifica-tions
Commentaires sur ces manuels