Jet Tools Drum Sander Manuel d'utilisateur

Operating Instructions and Parts Manual Drum Sander Model 22-44 Plus shown with optional infeed-outfeed tables and open stand WMH TOOL GROUP 2

10 Assembly Tools required for assembly: 1 Flat head screwdriver 1 Set of open-end wrenches 1 Set of Hex wrenches 1 Adjustable wrench Installing

11Dust Cover To open the dust cover, push in on the knob (C, Figure 5) and lift. The latch can be adjusted using the screw behind it. Dust Collection

12Successive windings of the strip should be flush with previous windings without any overlap. 5. Mark the trailing end of the strip where it crosse

13Grounding Instructions Electrical connections must be made by a qualified electrician in compliance with all relevant codes. This machine must be

14Extension Cords If an extension cord is necessary, make sure the cord rating is suitable for the amperage listed on the machine's motor plate.

15Conveyor Belt Tension and Tracking Conveyor belt tension adjustment may be necessary during the break-in period to compensate for belt stretching.

163. Loosen the conveyor take-up screw nuts (A, Figure 20) to relieve belt tension, and slide the driven roller fully inward. 4. Remove the four bol

17 5. If the drum does not contact the thickness gauge to the same degree as the opposite end of the drum, alignment is necessary. To align the drum

18NOTE: Keep track of how many revolutions of the fine tune knob are needed to change drum alignment for wider (over 22”) sanding. When sanding narro

191. Repeat “Tension Roller Alignment” except raise the sanding drum only 1/4 turn of the height adjustment handle. 2. If both tension rollers are

2 WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Serv

20Selecting SandSmart™ Feed Rates A faster feed rate allows faster sanding but fewer revolutions of the drum per inch of sanding. A slower feed rate

21If there is a significant thickness difference, the thinner pieces can slip on the conveyor belt if they do not contact the tension rollers. Also n

22Tracker Kit (98-0080) Trackers dramatically reduce tracking adjust-ments of conveyor belts. They are already installed on your sander. The followin

23Abrasive Selection Guide Grit Common Application 24...Abrasive planing, surfacing rough-sawn boards, maximum stock removal, glue removal. 36.

24Troubleshooting: Motor and Electrical Problems Trouble Probable Cause Remedy No incoming power. Check plug connections. Connect main cord to power

25Trouble Probable Cause Remedy Conveyor belt out of adjustment. Readjust conveyor belt; see page 15. Drive or driven roller needs adjusting. Read

26Troubleshooting: Operational Problems Trouble Probable Cause Remedy Ripples in sanded surface. (Non-uniformly spaced ripples). Uneven feed rate

27Trouble Probable Cause Remedy Line or groove in stock. Inconsistent feed rate. Do not stop or change the feed rate while feeding stock. Unsanded r

28Conveyor and Motor Assembly

29Parts List: Conveyor and Motor Assembly Index No. Part No. Description Size Qty 1...323759... Gear Motor ...

3 Table of Contents Table of Contents ...

30Drum Head Assembly

31Parts List: Drum Head Assembly Index No. Part No. Description Size Qty 1...70-4102... Motor, 1-3/4 HP, 110-120 Volt

3256...11-1000-04... Lock Washer, Internal Tooth ... 1/4”...2 57...

33Parts List: Open Stand – #609004 (Optional Accessory) Index Part No. No. Description Size Qty. 1...40-4040...

34Parts List: Closed Stand – #609005 (Optional Accessory) Index No. Part No. Description Size Qty 1...2244PLUS-401... Base...

35Parts List: Infeed and Outfeed Tables – #98-2202 (Optional Accessory) Index Part No. No. Description Size Qty. 1...2244PLUS-5

36Electrical Connections WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.com

4 Warning 1. Read and understand this entire manual before attempting assembly or operation. 2. Read and understand the warnings posted on the mac

5 blahblahblah 21. Make your workshop child proof with padlocks, master switches or by removing starter keys. 22. Give your work undivided attention

6 Introduction This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures for a JET Model 22-44 Plus Drum Sande

7 Features and Terminology The illustration below shows the major components and features of the 22-44 Plus Sander. These are referenced throughout t

8 Unpacking Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not disca

9 Assembling the Open Stand (Optional Accessory) (Refer to Figure 3. If further clarification is needed, consult the parts breakdown on page 35.) Too